Hard Disk Drive (II)

Most operating-system tools report capacity using the same abbreviations but actually use binary prefixes. For instance, the prefix mega-, which normally means 10⁶ (1,000,000), in the context of data storage can mean 2²⁰ (1,048,576), which is nearly 5% more. Similar usage has been applied to prefixes of greater magnitude. This results in a discrepancy between the disk manufacturer's stated capacity and the apparent capacity of the drive when examined through most operating-system tools. The difference becomes even more noticeable for a gigabyte (7%), and again for a terabyte (9%). For a petabyte there is a 11% difference between the SI (1000⁵) and binary (1024⁵) definitions. For example, Microsoft Windows reports disk capacity both in decimal-based units to 12 or more significant digits and with binary-based units to three significant digits. Thus a disk specified by a disk manufacturer as a 30 GB disk might have its capacity reported by Windows 2000 both as "30,065,098,568 bytes" and "28.0 GB". The disk manufacturer used the SI definition of "giga", 10⁹ to arrive at 30 GB; however, because Microsoft Windows, Mac OS and some Linux distributions use "gigabyte" for 1,073,741,824 bytes (2³⁰ bytes), the operating system reports capacity of the disk drive as (only) 28.0 GB

Form factors

The earliest “form factor” hard disk drives inherited their dimensions from floppy-disk drives (FDDs), so that either could be mounted in chassis slots, and thus the HDD form factors became colloquially named after the corresponding FDD types. "Form factor" compatibility continued after the 3½ inch size even though floppy disk drives with new smaller dimensions ceased to be offered.

• 8 inch: 9.5 in × 4.624 in × 14.25 in (241.3 mm × 117.5 mm × 362 mm)
  In 1979, Shugart Associates' SA1000 was the first form factor compatible HDD, having the same dimensions and a compatible interface to the 8″ FDD. Both "full height" and "half height" (2.313 in) versions were available.
• 5.25 inch: 5.75 in × 1.63 in × 8 in (146.1 mm × 41.4 mm × 203 mm)
  This smaller form factor, first used in an HDD by Seagate in 1980, was the same size as full height 5¼-inch diameter FDD, i.e., 3.25 inches high. This is twice as high as "half height" commonly used today; i.e., 1.63 in (41.4 mm). Most desktop models of drives for optical 120 mm disks (DVD, CD) use the half height 5¼″ dimension, but it fell out of fashion for HDDs. The Quantum Bigfoot HDD was the last to use it in the late 1990s, with “low-profile” (≈25 mm) and “ultra-low-profile” (≈20 mm) high versions.
• 3.5 inch: 4 in × 1 in × 5.75 in (101.6 mm × 25.4 mm × 146 mm) = 376.77344cm³
  This smaller form factor, first used in an HDD by Rodime in 1984, was the same size as the "half height" 3½″ FDD, i.e., 1.63 inches high. Today has been largely superseded by 1-inch high “slimline” or “low-profile” versions of this form factor which is used by most desktop HDDs.
• 2.5 inch: 2.75 in × 0.374–0.59 in × 3.945 in (69.85 mm × 9.5–15 mm × 100 mm) = 66.3575cm³-104.775cm³
  This smaller form factor was introduced by PrairieTek in 1988; there is no corresponding FDD. It is widely used today for hard-disk drives in mobile devices (laptops, music players, etc.) and as of 2008 replacing 3.5 inch enterprise-class drives. Today, the dominant height of this form factor is 9.5 mm for laptop drives, but high capacity drives have a height of 12.5 mm. Enterprise-class drives can have a height up to 15 mm.
• 1.8 inch: 54 mm × 8 mm × 71 mm = 30.672cm³
  This form factor, originally introduced by Integral Peripherals in 1993, has evolved into the ATA-7 LIF with dimensions as stated. It is increasingly used in digital audio players and sub notebooks. An original variant exists for 2–5 GB sized HDDs that fit directly into a PC card expansion slot. These became popular for their use in iPods and other HDD based MP3 players.
• 1 inch: 42.8 mm × 5 mm × 36.4 mm
  This form factor was introduced in 1999 as IBM's Microdrive to fit inside a CF Type II slot. Samsung calls the same form factor "1.3 inch" drive in its product literature.
• 0.85 inch: 24 mm × 5 mm × 32 mm
  Toshiba announced this form factor in January 2004 for use in mobile phones and similar applications, including SD/MMC slot compatible HDDs optimized for video storage on 4G handsets. Toshiba currently sells a 4 GB (MK4001MTD) and 8 GB (MK8003MTD) version and holds the Guinness World Record for the smallest harddisk drive.

Major manufacturers discontinued the development of new products for the 1-inch (1.3-inch) and 0.85-inch form factors in 2007, due to falling prices of flash memory, although Samsung introduced in 2008 with the SpinPoint A1 another 1.3-inch drive.

The inch-based nickname of all these form factors usually do not indicate any actual product dimension (which are specified in millimeters for more recent form factors), but just roughly indicate a size relative to disk diameters, in the interest of historic continuity.

Other characteristics

Data transfer rate (as of 2008) at the inner zone ranges from 44.2 MB/s to 74.5 MB/s, while the transfer rate at the outer zone ranges from 74.0 MB/s to 111.4 MB/s. In contrast, the first PC drives could manage only around 40 KiB/s.

Seek time currently ranges from just under 5 ms for high-end server drives, to 15 ms for miniature drives, with the most common desktop type typically being around 9 ms. There has not been any significant improvement in this speed for some years. Some early PC drives used a worm-gear to move the heads, and as a result had access times as slow as 80–120 ms, but this was quickly improved by voice-coil type actuation in the late 1980s, seeing access times reduce to around 20 ms.

Power consumption has become increasingly important, not just in mobile devices such as laptops but also in server and desktop markets. Increasing data center machine density has led to problems delivering sufficient power to devices, and getting rid of the waste heat subsequently produced, as well as environmental and electrical cost concerns (see green computing). Similar issues exist for large companies with thousands of desktop PCs. Smaller form factor drives often use less power than larger drives. One interesting development in this area is actively controlling the seek speed so that the head arrives at its destination only just in time to read the sector, rather than arriving as quickly as possible and then having to wait for the sector to come around (i.e. the rotational latency).

Audible noise (measured in dBa) is significant for certain applications, such as PvRs digital audio recording and quiet computers. Low noise disks typically use fluid bearings, slower rotational speeds (usually 5,400 rpm) and reduce the seek speed under load (AAM) to reduce audible clicks and crunching sounds. Drives in smaller form factors (e.g. 2.5 inch) are often quieter than larger drives.

Shock resistance is especially important for mobile devices. Some laptops now include a motion sensor that parks the disk heads if the machine is dropped, hopefully before impact, to offer the greatest possible chance of survival in such an event.

Access and interfaces

Hard disk drives are accessed over one of a number of bus types, including parallel ATA (PATA, also called IDE or EIDE), Serial ATA (SATA), SCSI, Serial Attached SCSI (SAS), and Fibre Channel. Bridge circuitry is sometimes used to connect hard disk drives to buses that they cannot communicate with natively, such as IEEE 1394 and USB.

Back in the days of the ST-506 interface, the data encoding scheme was also important. The first ST-506 disks used Modified Frequency Modulation (MFM) encoding, and transferred data at a rate of 5 megabits per second. Later on, controllers using 2,7 RLL (or just "RLL") encoding increased the transfer rate by 50%, to 7.5 megabits per second; this also increased disk capacity by fifty percent.

Many ST-506 interface disk drives were only specified by the manufacturer to run at the lower MFM data rate, while other models (usually more expensive versions of the same basic disk drive) were specified to run at the higher RLL data rate. In some cases, a disk drive had sufficient margin to allow the MFM specified model to run at the faster RLL data rate; however, this was often unreliable and was not recommended. (An RLL-certified disk drive could run on a MFM controller, but with 1/3 less data capacity and speed.)

Enhanced Small Disk Interface (ESDI) also supported multiple data rates (ESDI disks always used 2,7 RLL, but at 10, 15 or 20 megabits per second), but this was usually negotiated automatically by the disk drive and controller; most of the time, however, 15 or 20 megabit ESDI disk drives weren't downward compatible (i.e. a 15 or 20 megabit disk drive wouldn't run on a 10 megabit controller). ESDI disk drives typically also had jumpers to set the number of sectors per track and (in some cases) sector size.

Modern hard drives present a consistent interface to the rest of the computer, no matter what data encoding scheme is used internally. Typically a DSP in the electronics inside the hard drive takes the raw analog voltages from the read head and uses PRML and Reed–Solomon error correction to decode the sector boundaries and sector data, then sends that data out the standard interface. That DSP also watches the error rate detected by error detection and correction, and performs bad sector remapping, data collection for Self-Monitoring, Analysis, and Reporting Technology, and other internal tasks.

SCSI originally had just one speed, 5 MHz (for a maximum data rate of five megabytes per second), but later this was increased dramatically. The SCSI bus speed had no bearing on the disk's internal speed because of buffering between the SCSI bus and the disk drive's internal data bus; however, many early disk drives had very small buffers, and thus had to be reformatted to a different interleave (just like ST-506 disks) when used on slow computers, such as early IBM PC compatibles and early Apple Macintoshes.

ATA disks have typically had no problems with interleave or data rate, due to their controller design, but many early models were incompatible with each other and couldn't run in a master/slave setup (two disks on the same cable). This was mostly remedied by the mid-1990s, when ATA's specification was standardised and the details began to be cleaned up, but still causes problems occasionally (especially with CD-ROM and DVD-ROM disks, and when mixing Ultra DMA and non-UDMA devices).

Serial ATA does away with master/slave setups entirely, placing each disk on its own channel (with its own set of I/O ports) instead.

FireWire/IEEE 1394 and USB(1.0/2.0) HDDs are external units containing generally ATA or SCSI disks with ports on the back allowing very simple and effective expansion and mobility. Most FireWire/IEEE 1394 models are able to daisy-chain in order to continue adding peripherals without requiring additional ports on the computer itself......Continue

Data and source mostly taken from Wikipedia.